Browsing Makine Mühendisliği-Makale Koleksiyonu by Department "Mühendislik - Mimarlık Fakültesi"
Now showing items 1-20 of 31
-
Buckling analysis of laminated composite plates with an elliptical/circular cutout using FEM
(Elsevier Sci Ltd, 2010)In this study, a buckling analysis was carried out of a woven-glass-polyester laminated composite plate with an circular/elliptical hole, numerically. In the analysis, finite element method (FEM) was applied to perform ... -
A case study of hybrid wind-solar power system for reduction of CO2 emissions
(Inderscience Enterprises Ltd, 2012)In this study, the solar radiation and wind data pertaining to Bigadic region are analyzed to assess the performance of a hybrid Photovoltaic-Wind-Diesel-Battery energy system. The average energy consumption of the system ... -
Change in heating energy requirements for various interior space temperatures: A case study of Karabük
(2013)In this study, the effect of indoor temperature for heating on reduction of heating load in Karabuk province was studied for various cases. The potential heating degree-hour values for Karabuk are utilized by using average ... -
Design, manufacturing, and calibration process of one piece lathe dynamometer for measurement in two axes
(ASME, 2013)Many pieces in structure of a dynamometer may negatively affect the accuracy of the measurements since each piece may display a different strain and stress depending on its material and construction. A one piece dynamometer ... -
Designing of a diffusion bonding device by using solidworks 3-d design software
(Drunpp-Sarajevo, 2012)This article describes the designing of a solid-state diffusion. bonding device using 3-D design software named Solidworks. Designing of the geometry parametrically by the mentioned design software gives some flexibility ... -
A different approach aiming at fuel saving in a six cylinder internal combustion engines
(2012)In this study, two cylinders of a 1960 model six cylinder Dodge gasoline engine was shut off in low speed mode, and examined as to whether this operation reduces fuel consumption or not. For this purpose, a mechanical ... -
Diffusion bonding of pure copper and aluminium in argon gas atmosphere
(1997)The definition of diffusion welding accepted by the suggestion of N.F.Kazakov is given as follows [1]: Diffusion welding is a solid-state process where at a temperature high enough for diffusion to take place at interface ... -
Effect of clamping force on the delamination onset and growth in bolted composite laminates
(Elsevier Sci Ltd, 2012)Clamping force is a key element that alters the mechanism and sequence of failure in bolted joints of composite laminates. The mode of failure in bolted joints can be controlled by geometrical parameters and the preferred ... -
Effect of matrix structure on the impact properties of an alloyed ductile iron
(Elsevier Science Inc, 2006)An investigation was performed to examine the influence of the matrix structure on the impact properties of a 1.03% Cu, 1.25% Ni and 0.18% Mo pearlitic ductile iron. Specimens were first homogenized at 925 degrees C for 7 ... -
The effect of tool position for aluminum and copper at high rotational friction stir welding
(Pamukkale Univ, 2015)Friction Stir Welding (FSW) is a solid state welding process used for welding similar and dissimilar materials. This welding technique allows welding of Aluminum alloys which present difficulties in fusion joining and ... -
Energetic and exergetic performance evaluation of the quadruple-effect evaporator unit in tomato paste production
(Pergamon-Elsevier Science Ltd, 2010)Quadruple-effect evaporator units are commonly used in food focus area in sector is evaporative unit. It consumes about 60% of total energy input. The present study evaluates the performance of quadruple-effect evaporator ... -
Energy and exergy analyses of a raw mill in a cement production
(Pergamon-Elsevier Science Ltd, 2006)Cement production has been one of the most energy intensive industries in the world. In order to produce raw materials preparation, clinker and rotary kilns are widely used in cement plants. The objective of this study is ... -
Estimation of the monthly based hourly wind speed characteristics and the generated power characteristics for developing bidding strategies in an actual wind farm: A case study
(Springer Heidelberg, 2013)This manuscript proposes a new approach for the estimation of the monthly based hourly wind speed characteristics and the generated power characteristics in an actual wind farm. The proposed approach uses the probability ... -
Experimental investigation of the effect of diesel-cotton oil-n-butanol ternary blends on phase stability, engine performance and exhaust emission parameters in a diesel engine
(Elsevier Ltd, 2013)This study focused on the effect of temperature and component concentration on phase stability of diesel-cotton oil-n-butanol ternary blends. Titration method was performed for plotting phase diagrams at different temperatures ... -
Failure analysis of bolted joints in cross-ply composite laminates using cohesive zone elements
(Tech Science Press, 2013)A strength prediction method is presented for double-lap single fastener bolted joints of cross-ply carbon fibre reinforced plastic (CFRP) composite laminates using cohesive zone elements (CZEs). Three-dimensional finite ... -
FEM analysis of laminated composite plate with rectangular hole and various elastic modulus under transverse loads
(Elsevier Science Inc, 2010)The aim of this work is to predict the expansion of the plastic zone and residual stresses in layers of fiber-reinforced, thermoplastic laminated composite plates with rectangular hole. The effects of the material properties ... -
High-speed milling strategies in mould manufacturing
(Carl Hanser Verlag, 2010)High-speed cutting is one of the key issues in mould manufacturing. But to apply high-speed milling to mould manufacturing, unlike conventional milling, it is necessary to define specific cutting parameters. This article ... -
The influences of various parameters on the numerical solution of nonisothermal DAEM equation
(Elsevier Science Bv, 1999)This paper describes the effect of some parameters on the numerical solution of nonisothermal distributed activation energy model equation. Investigated parameters are integral upper limits, integral interval number, heating ... -
Investigation of environmental ımpacts of energy utilization in space heating
(Springer Verlag, 2013)This study presents the analysis of the energy and exergy utilization of the Bali{dotless}kesir space-heating sector (BSHS) in the years of 1996 and 2010 and environmental impacts of their usage. In this analysis, actual ... -
Mathematical modeling of heat recovery from a rotary kiln
(Pergamon-Elsevier Science Ltd, 2010)In this study, heat recovery from rotary kiln was examined for a cement plant in Turkey. At first, an exergy analysis was carried out on the operational data of the plant. Results indicated the presence of 217.31 GJ of ...
